Essential-Fundamental-Important Plumbing-Plumber Insights-Tips-Guide for Bathtub Installation-Installing a Bathtub
Essential-Fundamental-Important Plumbing-Plumber Insights-Tips-Guide for Bathtub Installation-Installing a Bathtub
Blog Article
This post which follows relating to How to Install a Bathtub is particularly interesting. Check it out yourself and figure out what you think of it.
Setting up a bathtub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bath tub with a new one is also a reasonably tough job. If the old tub is conveniently obtainable, the job can relocate immediately; if you have to open up a wall surface to eliminate the old bathtub as well as place the new tub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will certainly require an assistant to leave the old tub and embeded in the new one. See to it you have certified on your own for the task and fit trying it. Rather than employing a specialist to take over a halfway-completed project, it is far better to consider utilizing one prior to you start. Opportunities are you might need an expert plumber to make tube links.
This post will certainly help you mount a brand-new bathtub in your shower room if you have actually already gotten a brand-new tub as well as don't require to alter the setup of your previous supply of water pipelines.
Your tools and material list should make up the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you need to do is detach the water system. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be rather bothersome because of the restricted access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the tap and the sink. Secure the faucet in position with the maker supplied backnut. When the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap connectors. The former kind must be linked to the faucet finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing both wooden boards under its feet, put the bathtub in the required setting. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto four tiny points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the level and also adjusting the feet on the bath tub up until the level reads degree.
To mount taps, fit all-time low of the furthest adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water supply as well as check all joints and brand-new pipework for leaks as well as tighten them if required. Fill the bath tub and likewise inspect the overflow electrical outlet and also the regular outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling and also securing around the bath tub should wait until the tub has been used at least once as this will resolve it right into its final setting.
Planning for the Setup
First of all, the supporting structure provided with the bathroom needs to be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its last position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall between the bath as well as the tiling, causing issues with moisture and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealer can break relatively very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly readily available on the marketplace. It is suggested to fit the tiles making use of water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about How to Install a Bathtub? Give feedback below. We would be interested to find out your opinion about this write-up. We hope that you come back again in the near future. Those who appreciated our post plz don't forget to share it. We appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Rates Report this page